Installation of an Olarm MAX on Texecom Premier 168 Alarm Systems
Step 1: Programming your Texecom Premier 168 Alarm System
Enter the Engineers' code (default ‘1234’)
If the panel asks for a user to grant you access, enter a user code and retry
Press the ‘Down’ Key until you reach “UDL/Digi Options”, press 'yes/tick'
Press the ‘Down’ Key until you reach “UDL Options”, press 'yes/tick'
Press the ‘Down’ Key until you reach “UDL Password” is:
Press the ‘no/cross’ to edit it, enter your “UDL password”, then press 'yes/tick'
Take note of the UDL password for entering in the Olarm APP
Press the 'Menu' key once
Press the ‘Down’ Key until you reach “Setup Modules”, press 'yes/tick'
Press the ‘Down’ Key until you reach “Setup IP Data”, press 'yes/tick'
Press the ‘Down’ Key until you reach “ComIP Port”, press the ‘no/cross’ to edit it
Enter 10001, press 'yes/tick'
Press the ‘Down’ Key until you reach “ComIP Gateway”, press the ‘no/cross’ to edit it
Enter ‘192.168.000.001’, press 'yes/tick'
Press the Down Key until you reach “ComIP Netmask”, press the ‘no/cross’ to edit it
Enter ‘255.255.255.000’, press 'yes/tick'
Press the 'Menu' key once.
Continue to press the ‘Down’ Key until you reach “Com Port Setup”, press 'yes/tick'
Press the ‘Down’ Key until you reach “Com Port 1”, press ‘no/cross’
Press the ‘Down’ Key until you reach the “ComIP Module”, and press 'yes/tick'
Press 'Menu' until asked if you want to Exit and Logoff, press 'yes/tick'
Note: If Com Port 1 is in use, configure Com Port 2.
Step 2: Connect the Olarm MAX
Plug the 5-pin side of the reversible peripheral cable to the programmed Com Port on your Texecom Premier 168 Alarm System.
Cut and strip the 4-pin side of the cable. Wire this end into the terminals found on the back of the Olarm MAX.
Red to + (Positive)
Black to GND
Yellow to SERIAL 1
Green to SERIAL 2
Step 3: Enter the UDL code in the Olarm APP
Once you have powered up your Texecom Premier 168 alarm system, and have added it to the Olarm APP. You will be prompted to enter the UDL code in the app. Ensure this is the same UDL code that was programmed.
Related Articles
Installation of an Olarm MAX on Texecom Premier Alarm Systems
Step 1: Programme your Texecom Premier Alarm System Enter Engineering code Press the Programming Menu key Press [9] to enter the Programming Menu Enter [7] [6] to navigate to the Download Menu Press [2] to navigate to the UDL Passcode Enter [1 2 3 4] ...Troubleshooting an Olarm MAX installation on Texecom Premier Alarm Systems
Single Com Port Texecom Panels Should the Texecom alarm system only have one Com Port. The Olarm MAX may not be compatible due to a hardware limitation on the alarm system. Set the UDL passcode The UDL password must be set to 1234 for the Olarm MAX ...Installation of an Olarm MAX on Texecom Premier Elite Alarm Systems
Step 1: Programme the Texecom Premier Elite Alarm System Enter the Engineers code (default ‘1234’) If it says a user needs to grant you access, enter a user code and then retry. Press the ‘Down’ Key until you reach “UDL/Digi Options”, press yes/tick ...Troubleshooting an Olarm MAX installation on Texecom Premier 168 Alarm Systems
Ensure Olarm is connected to the correct Com Port Make sure the Olarm MAX is plugged into the Com Port that has been programmed on the panel. No device connected to Com 2? Enable it for IP Communications If Com 2 is unused, enable it for IP ...Installation of an Olarm MAX on Honeywell Galaxy 2 (G2) Alarm Systems
Installation Requirements An Olarm MAX G is required for this installation. If the Honeywell Galaxy 2 alarm system has an existing Ethernet Module & 3 Keypads, these must be removed before installing the Olarm MAX, as it will take their place. Step ...